How can one number hold a whole earthquake?
What you will find out
A magnitude is the first number everybody asks for after an earthquake. In this lesson the class learns what it measures, why one step means so much, and why the same earthquake can have several magnitudes.
- what magnitude measures and how Richter defined it
- why the scale is logarithmic: 10 times and 32 times
- the main scales: ML, mb, Ms and Mw
- how to compare two earthquakes by energy
One number for the whole earthquake
In 1935 Charles Richter needed a simple way to compare earthquakes in California. He measured the largest swing of the trace on a standard seismograph and corrected it for the distance to the station. The result was one number for each earthquake: its magnitude.
Magnitude measures the size of the earthquake at its source: how much energy was released. An earthquake has one magnitude, whoever measures it and wherever they stand.
ML = log₁₀(amplitude) + correction for distance
The scale is logarithmic. One step up means the ground at the same distance moves 10 times more, and the energy released is about 32 times greater. Two steps: 100 times the motion, about 1,000 times the energy.
Compare two earthquakes
Experiment
Set two magnitudes and compare.
First earthquake:
Second earthquake:
The small earthquake near Lake Paravani that our stations recorded on 19 November 2026 and the Spitak earthquake differ by about four units. That is roughly ten thousand times in ground motion and more than a million times in energy. The two were measured on different scales, so the comparison is approximate.
Why there are several magnitudes
Richter’s method works for nearby earthquakes of small and medium size. For others, seismologists use different waves, and so different scales.
| Scale | What is measured | Where it is used |
|---|---|---|
| ML, local | the largest amplitude on a nearby station | small and moderate earthquakes within a few hundred kilometres; our daily work |
| mb, body-wave | the first seconds of the P-wave | distant earthquakes |
| Ms, surface-wave | long surface waves with a period of about 20 s | large shallow earthquakes; Spitak 1988 was Ms 6.8 |
| Mw, moment | the seismic moment: rigidity of the rock × area of the rupture × slip | all sizes; the standard for large earthquakes |
The older scales saturate: above about magnitude 7 or 8 they stop growing, although the earthquake is bigger. The moment magnitude Mw does not, because it is tied to the physics of the source. This is why one earthquake can have slightly different numbers, such as “ML 2.5 · Mw 3.0” in our report of 18 November 2026.
energy in joules ≈ 10^(1.5 × M + 4.8)
The formulas
For a class that knows logarithms, here are the definitions used in seismology.
| Scale | Definition |
|---|---|
| ML (Richter, 1935) | ML = log₁₀ A − log₁₀ A₀(Δ), where A is the largest amplitude on a standard Wood–Anderson seismograph and A₀(Δ) is the amplitude of a magnitude 0 earthquake at the same distance Δ. By definition, an amplitude of 1 mm at 100 km gives ML = 3. |
| Ms | Ms = log₁₀(A/T) + 1.66 log₁₀ Δ + 3.3, with A the ground displacement in micrometres, T the period near 20 s and Δ the distance in degrees. |
| mb | mb = log₁₀(A/T) + Q(Δ, h), where Q is a tabulated correction for distance and depth. |
| Mw (Kanamori; Hanks and Kanamori, 1979) | Mw = ⅔ (log₁₀ M₀ − 9.1), with the seismic moment M₀ in newton-metres (Lesson 1). |
| Energy (Gutenberg and Richter) | log₁₀ E = 1.5 M + 4.8, with the radiated energy E in joules. |
The factor 1.5 in the last formula is where “32 times” comes from: 10^1.5 ≈ 31.6.
Four questions to close the case
0 of 4 correct
Magnitude describes…
How much more energy does a magnitude 7 release than a magnitude 5?
Why do seismologists prefer Mw for the largest earthquakes?
A station twice as far from the same earthquake records a smaller amplitude. The magnitude it gives is…
For the teacher: plan, answers, discussion
Plan (45 minutes)
- 0–10 min. Part 1. Recall logarithms: log 10 = 1, log 100 = 2.
- 10–25 min. Part 2 with the sliders; pupils fill a table for differences of 1, 2, 3 and 4 units.
- 25–35 min. Part 3: read the table of scales; find two magnitudes for one earthquake on our site.
- 35–45 min. Questions and discussion.
Answers
- Table: 1 unit: 10 × and about 32 ×. 2 units: 100 × and 1,000 ×. 3 units: 1,000 × and about 32,000 ×. 4 units: 10,000 × and 1,000,000 ×.
- Energy of a magnitude 5: about 2 × 10¹² J; of a magnitude 7: about 2 × 10¹⁵ J.
- Questions: 2, 3, 2, 2.
Questions for discussion
- Can a magnitude be negative? What would it mean?
- Why is “magnitude 6” on the news not enough to know how dangerous an earthquake was?
- News sometimes says “on the Richter scale” for Mw. What is wrong with that?
Data and examples: CHARNET seismic network, Institute of Geophysics and Engineering Seismology after A. Nazarov, Gyumri. iges.am